Speck-electronics EQ16 Uživatelský manuál Strana 11
- Strana / 33
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
7
The following information should give you the basics on how to install
the Model EQ16 and Power Supply. The proper installation of the
Model EQ16 as a part of a larger system requires a clear understanding
of audio wiring, AC distribution, grounding, and shielding techniques.
When the EQ16 is being installed into a larger system it may be
necessary to retain the services of someone experienced in these matters.
Before the EQ16 may be placed into its normal operating position, it
will be necessary to install the rack mount adapters.
The Model EQ16 may be installed into any 19" wide equipment rack
that uses standard E.I.A. universal spacing. The EQ16 may be affixed to
standard E.I.A. rack rails using (4) 10-32 machine screws.
The location of the EQ16 should be such that the operator has a clear,
unobstructed view of the front panel from his normal operating position.
The unit should also be within easy reach of the operators normal
position in order to facilitate the use of the front panel controls.
Any device that emits a high EMI (Electro Magnetic Interference) or
RFI (Radio Frequency Interference) energy field should be treated with
suspicion. EMI is considered any unwanted signal which adversely
affects the operation of the equalizer or the mixing system. This subject
is discussed in Chapter 5.
Electronic equipment such as power amplifiers, power supplies
(especially wall mount type), video monitors, computers, certain synths
and samplers must be located away from the EQ16 and its associated
cables. It may be necessary to alter the positions of certain equipment
that you feel would cause buzzes or hums in your audio system.
The PS3-0.8 power supply is supplied with the EQ16-16 (16 mono
channel version), and the higher powered PS3-1.5 is supplied with the
EQ16-32 (16 stereo channel version).
If you happen to be installing both versions of the Model EQ16 into
your system, it is extremely important that the PS3-0.8 supply only
be connected to the EQ16-16 and the PS3-1.5 only
be connected to
the EQ16-32.
General
Mechanical Installation
Installation
Physical Placement of
Adjacent Equipment
Power Supply
Chapter 3 Installation Section
- MODEL EQ16 1
- Warranty 2
- Edition 2
- Contents 3
- Chapter 4 Operation 4
- Chapter 5 Wiring and Other 4
- Introduction 5
- Figure 1b. Rear Panel Layout 6
- General Description 7
- Standard Accessories 7
- CAUTION! 8
- IMPORTANT! 8
- Rack mount adapters 8
- Initial Preparation 9
- Repacking For 10
- Shipment 10
- Installation 11
- Mounting location 12
- Configuring the AC 12
- Connecting the 13
- Power Supply 13
- Default Control 14
- Settings 14
- Rack Mount Adapters 14
- Interfacing the Model 15
- EQ16 Equalizer 15
- Cleaning 15
- Model EQ16 to a Mixer 16
- Interface to 18
- Operation 21
- FRONT PANEL CONTROLS 22
- Figure 10. Equalizer Channel 23
- REAR PANEL 27
- Headroom and 28
- Boost/Cut 28
- Wiring and Other 30
- Connectors 31
- Proper AC Grounding 31
- Proper Audio 32
- Grounding 32
- EMI and RFI 33
DeLOCK 84403 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Akcesoria komunikacja DeLOCK 84403.
Dostarczamy 2 pdf podręczników DeLOCK 84403 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentáře k této Příručce